|
1.
|
|
|
In the next steps we will configure your router in such a way that the router allows Zultrax P2P to accept incoming connections. Your router is designed to serve multiple computers and of course multiple programs. Even if there is only one computer connected we will later on need two bits of information:
- The local IP of your computer
- The port used by Zultrax P2P
|
|
Zultrax P2P can help you to find those two bits of information. In the menu tools choose system info. This will display a page of information with various details about the program amonst which Local IP and port. Write those 2 down, you'll need them later.
It is the Local IP we are looking for, do not confuse the Local IP with the Public IP that is also shown on this system info page.
|
|
|
|
2.
|
|
Exit Zultrax P2P. Don't leave the program running while you are performing the actions below. Leaving the program running might give you false indiciations that your actions where not succesfull.
|
|
|
|
3.
|
|
Open a webbrowser (e.g. Internet Explorer, Firefox or Opera). Enter the IP address of your router in the address bar of the browser and press enter. The IP address of your router is by default 10.0.0.2
|
|
|
4.
|
|
You see a box asking your username and password. By default the username for your Zoom 5654 router is admin and the password is zoomadsl
Enter your username and password and click the ok button to continue.
|
|
|
5.
|
|
Click on the button advanced setup.
You find this button on the top of the page.
|
|
|
6.
|
|
Click on the button nat.
You find this button on the center of the page.
|
|
|
7.
|
|
In the drop down box nat rule entry select the value nat option
|
|
|
8.
|
|
Click on the button add.
You find this button on the bottom of the page.
|
|
|
9.
|
|
You see a page titled NAT Rule - Add. Enter the fields as follows: | Rule Flavor | RDR | | Rule ID | 7. If you get a message because 7 is already used, try just another number above 1. | | IF Name | ALL | | Protocol | Any | | Local Address From | The local IP address you wrote down earlier | | Local Address To | The local IP address you wrote down earlier | | Global Address From | Leave this field empty | | Global Address To | Leave this field empty | | Destination Port From | Select Any Other Port and type the port number you wrote down earlier | | Destination Port To | The same as the field above, Any Other Port and port number.. | | Local Port | And one more time the same as above. | | |
|
|
|
|
10.
|
|
Click on the button save changes.
|
|
|
11.
|
|
Click on the button advanced setup.
You find this button on the top of the page.
|
|
|
12.
|
|
Click on the button ip filter.
You find this button on the center of the page.
|
|
|
13.
|
|
In the drop down box security level select the value none
|
|
|
14.
|
|
Select Accept in all three the fields, Public Default Action, Private Default Action and DMZ Default Action.
|
|
|
15.
|
|
Click the button #Name# to save your changes.
|
|
|
16.
|
|
|
|
Your Zoom 5654 router is configured now. You forwarded a port for Zultrax P2P. You can start Zultrax P2P and you will see incoming connections coming up. This might be not immediatly after start up but within minutes you should see at least some incoming connections. The program will adapt itself to the new configuration.
In case you still don't have incoming connections, perhaps you also have firewall software installed that needs configuration. For that see
the Firewalls/Routers page
, the info about firewall software is somewhere at the bottom of that page.
|
|
|
|
Zoom 5654
